Taping is designed to embed wallboard tape and trims. Taping joint compound is designed specifically for embedding drywall reinforcing tape. This product exhibits excellent shrinkage and a strong bond for a smooth, uniform wall surface. Taping compound is not recommended for the second and third coats over embedded tape, or as a texturing material. Meets ASTM C475.
Taping Joint Compound - 45 lb / 20.4 kg Box
For detailed product description please see the Product Data and Submittal Sheet
- Material: Vinyl-type mixture
- Color: Off white Packaging: 45 lb. (20.4 kg) Carton
- Coverage: 100 lb. (45.5 kg) to 150 lb. (68 kg) of joint compound per 1000 square feet (92.9 m2) of drywall depending upon the thickness of joint compound applied.
- Shelf Life: Please see the "Technical Guide - Finishing Product Shelf Life" for details
For complete Technical Data, please see the Product Data and Submittal Sheet
- Apply a thin layer of compound to the tapered edge. Press joint tape firmly into the compound, while centering it over the seam and embed with a broad knife. Sufficient joint compound must remain under the tape to ensure a proper bond. Allow to dry. Apply a second coat of joint compound over the embedding coat and feather out beyond the first coat. Allow the second coat to dry thoroughly prior to application of the finish coat. Spread the finish coat evenly over the second coat and feather to a smooth uniform finish. After each coat had dried, sand or sponge smooth prior to the application of the ensuing coat.
Finishing Beads & Trim:
- Apply first coat of compound to all the bead and trim and properly feather out onto the panel. Wet sand, as necessary. Allow the compound to dry thoroughly prior to the application of the second coat. Apply the second coat and feather at least 2" beyond first coat, allow to dry completely and wet sand, if necessary. Apply the finish coat and extend the compound slightly beyond the second coat. When dry, sand as necessary to provide a smooth surface for decoration.
- Sand with a wet sponge, if necessary, to eliminate dust and scuffing of the wallboard paper. Remove high spots using as few strokes as necessary. Clean the sponge frequently during use. If dry sanding is necessary, use 150 grit sand paper or finer. Lightly sand imperfections while being careful to avoid scuffing the paper. When dry sanding, wear a NIOSH approved dust mask and eye protection.
- Ensure that all surfaces to be decorated are thoroughly dry and dust free. Either a good quality drywall primer or an undiluted latex wall paint with a high solids content should be applied prior to painting, texturing or wallpapering. Adhere to all manufacturers' specific directions for painting and decorating materials.
For complete installation instructions, please see Product Data and Submittal Sheet, Installation Guide or Install Like the Pros
Since methods and conditions of application and storage, such as temperature, humidity, and over thinning are beyond our control, CertainTeed Gypsum, Inc. (CertainTeed) will not be responsible for the failure of this product when not used and stored according to directions and specifications and accepted standards of procedure inherent in drywall application; or when reasonable allowance is not made by the user for adverse weather and job conditions.
However, if this product proves to be defective, CertainTeed’s maximum liability shall be limited to replacement of the defective material only or refund of the original purchase price. CertainTeed will not be responsible for any other costs or expenses. These shall be the exclusive warranty and remedies provided by CertainTeed, including without limitation, the implied warranties or merchantability, fitness for use and fitness for a particular purpose. All claims shall be submitted in writing to CertainTeed within thirty days from the date of discovery. State or federal laws may provide rights in addition to this limited warranty that cannot be modified or excluded.
CertainTeed takes pride in providing the best solutions to make the spaces where we work, live, and play healthier and safer. This means offering high-performing products that create better living environments.
Our products improve building energy efficiency and reduce building energy consumption for the life of the structure. As a result, they help conserve nonrenewable energy sources, decrease dependence on hydrocarbons and lower greenhouse gas emissions.
CertainTeed’s ongoing commitment to sustainability in our manufacturing operations incorporates the principles of industrial ecology, managing energy and water, and reducing waste.
Our ecomedes Sustainable Product Platform allows you to quickly access the product information and certifications you need, calculate contributions to LEED and other green building rating systems and create and save a group of products using the project feature. The information is free to access and always up to date.