Regular Gypsum Board




 

Regular Gypsum Board

Regular Gypsum Board for use on interior walls and ceilings.
 
CertainTeed Regular Gypsum Boards are an interior gypsum board that consist of a solid set, fire-resistive gypsum core enclosed in ivory colored face paper and liner back paper. Long edges are slightly tapered, allowing joints to be reinforced and concealed with joint tape and joint compound. CertainTeed Regular Gypsum Boards are available in a variety of lengths and widths.

Regular Gypsum Board

Product Data:
  • Thicknesses: 1/4" (6.4 mm), 3/8" (9.5 mm), 1/2" (12.7 mm)
  • Widths: 4' (1220 mm) standard; 54" (1370 mm)
  • Lengths: 8' to 12' (2440 to 3660 mm) standard
  • Weight (approx.):
    1/4" (6.4 mm) – 1.13 lb/ft2 (5.5 kg/m2)
    3/8" (9.5 mm) – 1.25 lb/ft2 (6.1 kg/m2)
    1/2" (12.7 mm) – 1.60 lb/ft2 (7.8 kg/m2)
  • Core: Gypsum (noncombustible) premium quality natural (mined) gypsum, recycled gypsum and DSG (from flue gas desulphurisation, FGD) are used to manufacture Gypsum Board Products
  • Edges: 1/2" boards are available in square and tapered edge. 1/4" and 3/8" are available in 4' x 8' (1220 mm x 2440 mm) and tapered edge only.
  • End: Square – factory cut
  • Packaging: Two pieces per bundle, face-to-face and end-taped Special widths, lengths or edges may be available on special order. Consult your CertainTeed sales representative.
 
Special widths, lengths or edges may be available on special order. Consult your CertainTeed sales representative.
 
Applicable Standards:
  • meets ASTM C1396
      

For complete Technical Data, please see Product Data and Submittal Sheet.


Regular Gypsum Board

CertainTeed Regular Gypsum Board accepts most types of paints, texture and wall covering materials. The surface shall be primed and sealed with a full-bodied latex primer before applying a final decorative material. This will equalize the suction between the joint compounds and the paper surface. For best painting results, all surfaces, including joint compound, should be clean, dust-free and not glossy. If glossy paints are used, a thin skim coat of compound over the entire surface, Level 5 finish, is recommended to reduce highlighting or joint photographing. This method is also recommended for areas of critical sidelighting of natural or artificial light sources. A sealer application under wallpaper or other wall covering is also recommended so the board surface will not be damaged if the covering is subsequently removed during redecorating. Joint treatment must be thoroughly dry before proceeding with primer-sealer application and final decoration.

Applicable Standards and References
  • ASTM C840
  • GA-216
  • GA-214



Regular Gypsum Board

Please see the attached document for the complete warranty.

Regular Gypsum Board

CertainTeed Gypsum is committed to sustainability. Our 14 gypsum board manufacturing facilities, located throughout North America, operate with a responsible and environmentally conscious ethic that includes reclamation, preservation of natural resources, recycling and waste management.
  
The face and back paper used for our gypsum boards consists of 100% recycled paper and in-plant scrap is recycled back into the manufacturing process. Where sources are available, synthetic or “by-product” gypsum from the desulphurization of flue gases at coal-fired power plants is used. Currently three of our manufacturing plants (Carrollton, Kentucky; Moundsville, West Virginia and Toronto, Ontario) use 100% synthetic gypsum and the total recycled content for these synthetic gypsum plants is 96%.

Although LEED rating systems do not currently address emissions for all building materials and their effects on indoor air quality, finished CertainTeed gypsum board products have no reportable VOCs and will not affect indoor air quality.

 
Search CertainTeed.com
| Entire Site |